- Oregon Scientific Weather Station Bar206a Manual
- Oregon Scientific Weather Station Manual Bar218hg
- Oregon Scientific Weather Station Instruction Manual Z111
- Oregon Scientific Weather Station Manual Bar 206
View and Download Oregon Scientific BAR208HGA user manual online. Advanced Weather Station with Atomic Time. BAR208HGA Weather Station pdf manual download. View online Operation & user’s manual for Oregon Scientific BAA928U Weather Station or simply click Download button to examine the Oregon Scientific BAA928U guidelines offline on your desktop.
Advanced Weather Station
Thank you for selecting this Oregon ScientificTM Wireless Weather Forecaster with Temperature Display and Self - Setting Atomic Clock (BAR686A). This clock is supplied with a remote sensor (THN122N) and can support up to 3 sensors in total (additional sensors sold separately). NOTE Please keep this manual handy as you use your new product. View and Download Oregon Scientific BAR206 user manual online. Weather Forecast Station with Atomic Time. BAR206 Weather Station pdf manual download. Also for: Bar206a. Hereby, Oregon Scientific, declares that this Advanced Weather Station with Atomic Time (Model: BAR208HG) is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the signed and dated Declaration of Conformity is available on request via our Oregon Scientific Customer Service. Portable Weather Radio (WR601N) from Oregon Scientific™. The WR601N is a multi-function device that operates on the same radio frequencies used by the NOAA Weather Radio (NWR) and Weatheradio Canada. With an Early Alert system, users are alerted to weather and other environmental dangers.
with Atomic Time
Model: BAR208HGA
USER MANUAL
EN
OVERVIEW
FRONT VIEW (FIG 1)
1. Remote sensor reception indicator
2. Moon phase reading
3. Weather forecast
4. Indoor temperature with temperature trend
5. Clock signal reception indicator
6. MODE: Change settings / display
7.
/
: Increase / decrease settings; activate / deacti
vate clock reception signal
8. Outdoor temperature with temperature trend
9. Outdoor humidity with humidity trend
10. Weather warning message
11. Indoor humidity with humidity trend
12. Time zone
13. Clock with weekday
14. MEM: View current, maximum and minimum
temperature / humidity
15. LIGHT: Activate backlight for 5 seconds
16. Ice alert LED indicator
BACK VIEW (FIG 2)
6
1
2
3
4
5
7
14
8
9
10
11
13
15
16
12
1. °C / °F: Select temperature unit
2. RESET: Reset unit to default settings
REMOTE SENSOR (FIG 3)
1. LCD display
2. LED status indicator
3. Wall mount hole
4. RESET hole
5. CHANNEL switch
6. Battery compartment
GETTING STARTED
INSERT BATTERIES
1. Remove the battery compartment.
2. Insert the batteries, matching the polarities (see FIG 2).
3. Press RESET after each battery change.
LOCATION
MEANING
Clock / alarm and
Main unit batteries low
Indoor temperature area
Outdoor temperature area
Sensor batteries low
REMOTE SENSOR
The main unit can collect data from up to 3 sensors.
To set up the sensor:
1. Open the battery compartment with a small Philips
screwdriver and insert batteries, matching the polarity.
2. Select a channel then press RESET.
3. Close the battery door.
4. Place the sensor within 30 m (98 ft) of the main unit
using the table stand or wall mount.
TIP Ideal placements for the sensor would be in any
location on the exterior of the home at a height of not more
than 5 ft and which can shield it from direct sunlight or wet
conditions for an accurate reading.
NOTE Use alkaline batteries for longer usage and consumer
grade lithium batteries in temperatures below freezing.
SENSOR DATA TRANSMISSION
To search for a sensor:
Press and hold
+ MODE.
The sensor reception icon in the remote sensor area shows
the status:
ICON
DESCRIPTION
Main unit is searching for sensor(s).
A channel has been found.
The sensor cannot be found.
TIP The transmission range may vary depending on many
factors. You may need to experiment with various locations to
get the best results.
1
2
1
2
3
4
5
6
CLOCK
CLOCK RECEPTION
This product is designed to synchronize its clock
automatically with WWVB-60 signal, within 3200km (2000
miles) of Fort Collins Colorado.
To enable / disable signal reception:
Press and hold to
enable or
to disable signal reception.
NOTE Reception takes 2-10 minutes. If the signal is weak,
it can take up to 24 hours to get a valid signal. If signal
reception is unsuccessful, place your unit next to a window,
press and hold
to force another signal search.
Clock signal reception indicator:
STRONG SIGNAL WEAK SIGNALNO SIGNAL
MANUALLY SET CLOCK
To set the clock manually, disable the signal reception first.
1. Press and hold MODE.
2. Press
or
to change the settings.
3. Press MODE to confirm.
4. The settings order is: time zone, 12/24 hr format, hour,
minute, year, calendar mode (day – month / month
– day), month, day and language.
Select the time zone: (P) Pacific, (E) Eastern, (C) Central or
(M) Mountain.
NOTE The language options are English (E), German (D),
French (F), Italian (I), and Spanish (S).
Oregon Scientific Weather Station Bar206a Manual
To select display mode:
Press MODE to choose between clock with seconds /
weekday / calendar / moon phase.
WEATHER FORECAST
This product forecasts the next 12 to 24 hours of weather
within a 30-50 km (19-31 mile) radius (US- with a 75%
accuracy).
Sunny
Partially Cloudy
Cloudy
Rainy
Snowy
WEATHER WARNING MESSAGE
The weather warning messages provide indications of
probable circumstances that may arise based on the weather
station’s calculations. The meanings for the warnings are
illustrated below:
Warning
Meaning
Risk of high temperatures
Risk of fast wind speeds
Risk of a storm
Risk of foggy conditions
Risk of icy conditions
Oregon Scientific Weather Station Manual Bar218hg
TEMPERATURE AND HUMIDITY
To toggle temperature unit:
Press °C / °F.
To auto-scan between sensors:
Oregon Scientific Weather Station Instruction Manual Z111
Press and hold
+ MEM to display each sensor’s data for
3 seconds.
Oregon Scientific Weather Station Manual Bar 206
To end press
.
To toggle between current, minimum and maximum
records for the selected sensor:
Press MEM repeatedly.
To clear the records:
Press and hold MEM.
ICE WARNING
If the channel 1 sensor falls between 3°C to -2 °C (37°F to
28°F), LED indicator will flash, and will stop flashing once the